Watch Winder Settings for Hamilton: TPD and Direction

Set a Hamilton winder to the 650–800 TPD band and check the direction before anything else. The 2 automatic calibres listed here need between 240 and 240 TPD to hold a full wind, because the reserve is 80 hours.

Recommended band650–800 TPD
Calculated minimum240 TPD
DirectionBidirectional
Coverage2 automatic · 80 h

Hamilton TPD and direction by calibre

Calibre Type Reserve (h) Beat (vph) Direction Min TPD Recommended Note
H-10 (ETA C07.111 base) Automatic 80 21,600 Bidirectional 240 650–800 —
H-12 Automatic 80 21,600 Bidirectional 240 650–800 Day-date version of the H-10

Rows marked n/a are hand-wound or quartz. A winder adds nothing to either: no rotor to turn, or no mainspring to hold. Full method and the other 38 brands are in the TPD settings database.

What makes Hamilton different

Hamilton’s H-10 and H-12 are the same 80-hour, 21,600 vph architecture used across the Swatch Group’s Powermatic family.

240 TPD holds them. There is no reason to run the default band on an 80-hour movement.

Setting a Hamilton winder in four steps

  1. Set the direction first. Bidirectional for the automatics on this page. Direction is the setting that silently does nothing when it is wrong.
  2. Wind to full on the published band. Run 650–800 TPD for 48 hours to fill the mainspring from stopped. Do not start at the calculated minimum — that figure holds a wind, it does not build one.
  3. Check the power reserve. After 48 hours, take the watch off and let it run down. Full reserve means the setting works. Short means raise TPD or reverse the direction.
  4. Back the setting down if you want less wear. Once the reserve is confirmed, the calculated minimum (240 TPD) holds the watch at full wind with fewer cycles. This is optional, not required.

Winders that can be set to these numbers

Per-rotor TPD and direction programming is the only requirement — a winder with a single fixed programme cannot follow the table above.

Frequently asked questions

What TPD should I set for a Hamilton watch winder?

650–800 TPD is the band to start with. The calculated minimum — the turns that replace one day of running — is 240–240 TPD for the calibres on this page. Start on the band for 48 hours to fill a stopped watch, then back the setting down towards the calculated figure if you want less wear.

Which direction should a Hamilton winder turn?

Bidirectional. Every automatic Hamilton calibre in this database winds in both directions, so either setting works. If the watch shows no gain after 48 hours, the problem is the TPD, not the direction.

Can I leave a Hamilton on the winder permanently?

Yes, at a setting near the calculated minimum. Hamilton reserves here run 80 h, so 240–240 TPD holds the watch at full wind without cycling the mainspring more than necessary. Check the reserve after 48 hours before settling on a permanent setting.

Is a higher TPD better for a Hamilton?

No. TPD only has to replace what the movement consumes. On a 80-hour Hamilton calibre that is 240 TPD; running 800 or 1000 keeps the mainspring at full tension and cycles it more often for no gain.

Where do these Hamilton figures come from?

Reserve and beat rate are manufacturer-published figures for each calibre; direction and the recommended band are published workshop practice. Only the Minimum TPD column is calculated: 24 ÷ reserve hours × 800, rounded. Full method and the CSV download are on the TPD settings database.

Source, version and citation

Figures are from Aurawinder’s Watch Winder TPD Settings Database, version 2.0, updated 9 November 2026, released under CC BY 4.0. The minimum TPD column is calculated as round(24 ÷ reserve hours × 800, -1); every other figure is published data. Reuse is allowed with attribution.

Cite this data

CC BY 4.0 · free to reuse · keep the link
Plain text
Aurawinder. "Hamilton Watch Winder TPD Settings," database version 2.0, updated 9 November 2026. https://www.aurawinder.com/tpd/hamilton/ (CC BY 4.0).
HTML link
<a href="https://www.aurawinder.com/tpd/hamilton/">Aurawinder TPD Database: Hamilton</a>
Badge
Aurawinder TPD Database — Hamilton
Need the numbers in a spreadsheet? Download the Hamilton table as CSV · full database on the TPD settings database.

Found an error, or a Hamilton calibre that should be here? Tell us — corrections are logged in the database changelog.

Further reading

Product was successfully added to your cart!