Watch Winder Settings for Rolex: TPD and Direction

Set a Rolex winder to the 650–800 TPD band and check the direction before anything else. The 8 automatic calibres listed here need between 270 and 400 TPD to hold a full wind, because the reserves run 48–72 hours.

Recommended band650–800 TPD
Calculated minimum270–400 TPD
DirectionBidirectional
Coverage8 automatic · 48–72 h

Rolex TPD and direction by calibre

Calibre Type Reserve (h) Beat (vph) Direction Min TPD Recommended Note
Calibre 4130 (Daytona) Automatic 72 28,800 Bidirectional 270 650–800 Chronograph; same range as time-only
Calibre 3131 (Milgauss) Automatic 48 28,800 Bidirectional 400 650–800 Additional internal magnetic shielding
Calibre 3135 Automatic 48 28,800 Bidirectional 400 650–800 Time-only workhorse, 1988–2020; perpetual rotor — avoid a high default TPD
Calibre 3235 Automatic 70 28,800 Bidirectional 270 650–800 70 h reserve; needs far fewer turns than a 3135
Calibre 3230 Automatic 70 28,800 Bidirectional 270 650–800 No-date 3235
Calibre 3285 (GMT-Master II) Automatic 70 28,800 Bidirectional 270 650–800 —
Calibre 3186 (GMT-Master II) Automatic 48 28,800 Bidirectional 400 650–800 Pre-2018 GMT
Calibre 9001 (Sky-Dweller) Automatic 72 28,800 Bidirectional 270 650–800 Annual calendar; most complex Rolex automatic

Rows marked n/a are hand-wound or quartz. A winder adds nothing to either: no rotor to turn, or no mainspring to hold. Full method and the other 38 brands are in the TPD settings database.

What makes Rolex different

Every Rolex automatic here is bidirectional, so the only real variable is the reserve. The 31xx family runs 48 hours and needs 400 TPD; the 32xx family runs 70 and needs 270.

That gap is the whole point of the calculated column. A 3235 held at 400 TPD is being wound harder than it needs, and a 3135 held at 270 will slowly run down. The 4130 chronograph and the 9001 annual calendar both sit at 72 hours, so they follow the 32xx figure.

Setting a Rolex winder in four steps

  1. Set the direction first. Bidirectional for the automatics on this page. Direction is the setting that silently does nothing when it is wrong.
  2. Wind to full on the published band. Run 650–800 TPD for 48 hours to fill the mainspring from stopped. Do not start at the calculated minimum — that figure holds a wind, it does not build one.
  3. Check the power reserve. After 48 hours, take the watch off and let it run down. Full reserve means the setting works. Short means raise TPD or reverse the direction.
  4. Back the setting down if you want less wear. Once the reserve is confirmed, the calculated minimum (270–400 TPD) holds the watch at full wind with fewer cycles. This is optional, not required.

Winders that can be set to these numbers

Per-rotor TPD and direction programming is the only requirement — a winder with a single fixed programme cannot follow the table above.

Frequently asked questions

What TPD should I set for a Rolex watch winder?

650–800 TPD is the band to start with. The calculated minimum — the turns that replace one day of running — is 270–400 TPD for the calibres on this page. Start on the band for 48 hours to fill a stopped watch, then back the setting down towards the calculated figure if you want less wear.

Which direction should a Rolex winder turn?

Bidirectional. Every automatic Rolex calibre in this database winds in both directions, so either setting works. If the watch shows no gain after 48 hours, the problem is the TPD, not the direction.

Can I leave a Rolex on the winder permanently?

Yes, at a setting near the calculated minimum. Rolex reserves here run 48–72 h, so 270–400 TPD holds the watch at full wind without cycling the mainspring more than necessary. Check the reserve after 48 hours before settling on a permanent setting.

Is a higher TPD better for a Rolex?

No. TPD only has to replace what the movement consumes. On a 72-hour Rolex calibre that is 270 TPD; running 800 or 1000 keeps the mainspring at full tension and cycles it more often for no gain.

Where do these Rolex figures come from?

Reserve and beat rate are manufacturer-published figures for each calibre; direction and the recommended band are published workshop practice. Only the Minimum TPD column is calculated: 24 ÷ reserve hours × 800, rounded. Full method and the CSV download are on the TPD settings database.

Source, version and citation

Figures are from Aurawinder’s Watch Winder TPD Settings Database, version 2.0, updated 9 November 2026, released under CC BY 4.0. The minimum TPD column is calculated as round(24 ÷ reserve hours × 800, -1); every other figure is published data. Reuse is allowed with attribution.

Cite this data

CC BY 4.0 · free to reuse · keep the link
Plain text
Aurawinder. "Rolex Watch Winder TPD Settings," database version 2.0, updated 9 November 2026. https://www.aurawinder.com/tpd/rolex/ (CC BY 4.0).
HTML link
<a href="https://www.aurawinder.com/tpd/rolex/">Aurawinder TPD Database: Rolex</a>
Badge
Aurawinder TPD Database — Rolex
Need the numbers in a spreadsheet? Download the Rolex table as CSV · full database on the TPD settings database.

Found an error, or a Rolex calibre that should be here? Tell us — corrections are logged in the database changelog.

Further reading

Product was successfully added to your cart!