Watch Winder Settings for Seiko: TPD and Direction

Set a Seiko winder to the 650–800 TPD band and check the direction before anything else. The 7 automatic calibres listed here need between 270 and 480 TPD to hold a full wind, because the reserves run 40–70 hours.

Recommended band650–800 TPD
Calculated minimum270–480 TPD
DirectionBidirectional
Coverage7 automatic · 40–70 h

Seiko TPD and direction by calibre

Calibre Type Reserve (h) Beat (vph) Direction Min TPD Recommended Note
NH35 / NH36 Automatic 41 21,600 Bidirectional 470 650–800 —
7S26 Automatic 40 21,600 Bidirectional 480 650–800 Magic Lever winding
4R35 Automatic 41 21,600 Bidirectional 470 650–800 —
4R36 Automatic 41 21,600 Bidirectional 470 650–800 Day-date
6R15 Automatic 50 21,600 Bidirectional 380 650–800 —
6R35 Automatic 70 21,600 Bidirectional 270 650–800 —
8L35 Automatic 50 28,800 Bidirectional 380 650–800 Grand Seiko-built, 28,800 vph

Rows marked n/a are hand-wound or quartz. A winder adds nothing to either: no rotor to turn, or no mainspring to hold. Full method and the other 38 brands are in the TPD settings database.

What makes Seiko different

Seiko’s Magic Lever winds efficiently in both directions, so the brand almost never needs a high setting. The 4R and 7S calibres run 40–41 hours and need 470–480 TPD; the 6R35 runs 70 and needs 270.

Spring Drive 9R-series movements are auto-wound but quartz-regulated: TPD affects the reserve and never the rate. The 8L35 is the one 28,800 vph exception.

Setting a Seiko winder in four steps

  1. Set the direction first. Bidirectional for the automatics on this page. Direction is the setting that silently does nothing when it is wrong.
  2. Wind to full on the published band. Run 650–800 TPD for 48 hours to fill the mainspring from stopped. Do not start at the calculated minimum — that figure holds a wind, it does not build one.
  3. Check the power reserve. After 48 hours, take the watch off and let it run down. Full reserve means the setting works. Short means raise TPD or reverse the direction.
  4. Back the setting down if you want less wear. Once the reserve is confirmed, the calculated minimum (270–480 TPD) holds the watch at full wind with fewer cycles. This is optional, not required.

Winders that can be set to these numbers

Per-rotor TPD and direction programming is the only requirement — a winder with a single fixed programme cannot follow the table above.

Why the 4R family needs less than you think

4R35 and 4R36 carry roughly 41 hours of reserve, so a setting built for a 70-hour movement will keep the mainspring pinned at full tension for no benefit. The 6R35 is the exception in this family at around 70 hours, and it is the one Seiko calibre where the higher band is genuinely earned.

Frequently asked questions

What TPD should I set for a Seiko watch winder?

650–800 TPD is the band to start with. The calculated minimum — the turns that replace one day of running — is 270–480 TPD for the calibres on this page. Start on the band for 48 hours to fill a stopped watch, then back the setting down towards the calculated figure if you want less wear.

Which direction should a Seiko winder turn?

Bidirectional. Every automatic Seiko calibre in this database winds in both directions, so either setting works. If the watch shows no gain after 48 hours, the problem is the TPD, not the direction.

Can I leave a Seiko on the winder permanently?

Yes, at a setting near the calculated minimum. Seiko reserves here run 40–70 h, so 270–480 TPD holds the watch at full wind without cycling the mainspring more than necessary. Check the reserve after 48 hours before settling on a permanent setting.

Is a higher TPD better for a Seiko?

No. TPD only has to replace what the movement consumes. On a 70-hour Seiko calibre that is 270 TPD; running 800 or 1000 keeps the mainspring at full tension and cycles it more often for no gain.

Where do these Seiko figures come from?

Reserve and beat rate are manufacturer-published figures for each calibre; direction and the recommended band are published workshop practice. Only the Minimum TPD column is calculated: 24 ÷ reserve hours × 800, rounded. Full method and the CSV download are on the TPD settings database.

Source, version and citation

Figures are from Aurawinder’s Watch Winder TPD Settings Database, version 2.0, updated 9 November 2026, released under CC BY 4.0. The minimum TPD column is calculated as round(24 ÷ reserve hours × 800, -1); every other figure is published data. Reuse is allowed with attribution.

Cite this data

CC BY 4.0 · free to reuse · keep the link
Plain text
Aurawinder. "Seiko Watch Winder TPD Settings," database version 2.0, updated 9 November 2026. https://www.aurawinder.com/tpd/seiko/ (CC BY 4.0).
HTML link
<a href="https://www.aurawinder.com/tpd/seiko/">Aurawinder TPD Database: Seiko</a>
Badge
Aurawinder TPD Database — Seiko
Need the numbers in a spreadsheet? Download the Seiko table as CSV · full database on the TPD settings database.

Found an error, or a Seiko calibre that should be here? Tell us — corrections are logged in the database changelog.

Further reading

Product was successfully added to your cart!