Watch Winder Settings for Sellita: TPD and Direction

Set a Sellita winder to the 650–800 TPD band and check the direction before anything else. The 4 automatic calibres listed here need between 440 and 510 TPD to hold a full wind, because the reserves run 38–44 hours.

Recommended band650–800 TPD
Calculated minimum440–510 TPD
DirectionBidirectional (SW200-1, SW300-1, SW330-1); Clockwise (SW500)
Coverage4 automatic · 38–44 h

Sellita TPD and direction by calibre

Calibre Type Reserve (h) Beat (vph) Direction Min TPD Recommended Note
SW200-1 Automatic 38 28,800 Bidirectional 510 650–800 2824 replacement
SW500 (7750 architecture) Automatic 44 28,800 Clockwise 440 800–1000 —
SW300-1 Automatic 42 28,800 Bidirectional 460 650–800 2892 replacement
SW330-1 Automatic 42 28,800 Bidirectional 460 650–800 GMT

Rows marked n/a are hand-wound or quartz. A winder adds nothing to either: no rotor to turn, or no mainspring to hold. Full method and the other 38 brands are in the TPD settings database.

What makes Sellita different

Sellita mirrors ETA almost exactly: SW200-1 at 38 hours (510 TPD), SW300-1 and SW330-1 at 42 (460 TPD), all bidirectional.

The exception is the SW500, which is the 7750 architecture and therefore winds clockwise only, with a 440 floor inside a higher 800–1000 band.

Setting a Sellita winder in four steps

  1. Set the direction first. Bidirectional for the automatics on this page, with the exceptions noted in the table. Direction is the setting that silently does nothing when it is wrong.
  2. Wind to full on the published band. Run 650–800 TPD for 48 hours to fill the mainspring from stopped. Do not start at the calculated minimum — that figure holds a wind, it does not build one.
  3. Check the power reserve. After 48 hours, take the watch off and let it run down. Full reserve means the setting works. Short means raise TPD or reverse the direction.
  4. Back the setting down if you want less wear. Once the reserve is confirmed, the calculated minimum (440–510 TPD) holds the watch at full wind with fewer cycles. This is optional, not required.

Winders that can be set to these numbers

Per-rotor TPD and direction programming is the only requirement — a winder with a single fixed programme cannot follow the table above.

Frequently asked questions

What TPD should I set for a Sellita watch winder?

650–800 TPD is the band to start with. The calculated minimum — the turns that replace one day of running — is 440–510 TPD for the calibres on this page. Start on the band for 48 hours to fill a stopped watch, then back the setting down towards the calculated figure if you want less wear.

Which direction should a Sellita winder turn?

Not the same for every calibre. Most are bidirectional, but SW500 (clockwise) wind in one direction only. Wrong direction means the rotor freewheels and the watch runs down while the winder turns.

Can I leave a Sellita on the winder permanently?

Yes, at a setting near the calculated minimum. Sellita reserves here run 38–44 h, so 440–510 TPD holds the watch at full wind without cycling the mainspring more than necessary. Check the reserve after 48 hours before settling on a permanent setting.

Is a higher TPD better for a Sellita?

No. TPD only has to replace what the movement consumes. On a 44-hour Sellita calibre that is 440 TPD; running 800 or 1000 keeps the mainspring at full tension and cycles it more often for no gain.

Where do these Sellita figures come from?

Reserve and beat rate are manufacturer-published figures for each calibre; direction and the recommended band are published workshop practice. Only the Minimum TPD column is calculated: 24 ÷ reserve hours × 800, rounded. Full method and the CSV download are on the TPD settings database.

Source, version and citation

Figures are from Aurawinder’s Watch Winder TPD Settings Database, version 2.0, updated 9 November 2026, released under CC BY 4.0. The minimum TPD column is calculated as round(24 ÷ reserve hours × 800, -1); every other figure is published data. Reuse is allowed with attribution.

Cite this data

CC BY 4.0 · free to reuse · keep the link
Plain text
Aurawinder. "Sellita Watch Winder TPD Settings," database version 2.0, updated 9 November 2026. https://www.aurawinder.com/tpd/sellita/ (CC BY 4.0).
HTML link
<a href="https://www.aurawinder.com/tpd/sellita/">Aurawinder TPD Database: Sellita</a>
Badge
Aurawinder TPD Database — Sellita
Need the numbers in a spreadsheet? Download the Sellita table as CSV · full database on the TPD settings database.

Found an error, or a Sellita calibre that should be here? Tell us — corrections are logged in the database changelog.

Further reading

Product was successfully added to your cart!